LITHIUM COMPATIBLE PRODUCTS
DIAGNOSTICS, RE-PROGRAMMING, ABS BRAKE BLEEDING
BSU2-50 provides a stable voltage and up to 50 amps (dependent on model) of fully regulated power to prevent loss of charge and damage to the battery.
BSU2-50 can be used with any 12V automotive battery including AGM, GEL and lithium.
When the battery is charged the BSU is a regulated power supply to sustain accessory loads and offset parasitic drain.
Designed for use in the workshop and compatible with most diagnostic trolleys.
Reverse polarity protection.
Output current display.
Contactor reset for lithium batteries.
Supplied with IEC power lead and 5m output leads.
DIAGNOSTICS, RE-PROGRAMMING, ABS BRAKE BLEEDING
BSU2-50 provides a stable voltage and up to 50 amps (dependent on model) of fully regulated power to prevent loss of charge and damage to the battery.
BSU2-50 can be used with any 12V automotive battery including AGM, GEL and Lithium Iron (LiFePO4).
When the battery is charged the BSU is a regulated power supply to sustain accessory loads and offset parasitic drain.
Can be used in the showroom to maintain the battery charge while power consuming accessories are being demonstrated without fear of power loss.
Reverse polarity protection.
Supplied with 4.8M lead set and 2.4M IEC power lead.
BSU2-50 - UK JLR Dealers click here
This low profile (90mm) battery conditioner has been designed specifically for car showrooms.
Most conventional battery conditioners simply trickle charge the battery after it has been drained. The SSU2-50 provides instant support to the battery negating the need for recharging.
With the SSU2-50 Showroom connected to your vehicles you can be sure that they are always ready for demonstration and that the battery will be kept in prime condition.
This unit has been designed to slip under most vehicles without risk of damage to floor and features automatic current sensing so that it knows when it is needed.
The intelligent sensing in the SSU2-50 determines exactly when support is required to minimize unnecessary noise and power consumption.
An expanding range of adaptors are also available to allow simple connection directly to the vehicle battery or via distribution points.
The new SSU2-50/S provides a stable voltage and up to 50 amps of fully regulated power to prevent loss of charge and damage to the battery without any fan noise ensuring a noise free environment for your sales customers.
SSU2-50/S can be used with any 12V automotive battery including AGM and GEL.
When the battery is charged the SSU is a regulated power supply to sustain accessory loads and offset parasitic drain.
This low profile (90mm) battery conditioner has been designed specifically for car showrooms.
Most conventional battery conditioners simply trickle charge the battery after it has been drained. The SSU2-50/S provides instant support to the battery negating the need for recharging.
With the SSU2-50/S showroom conditioner connected to your vehicles you can be sure that they are always ready for demonstration and that the battery will be kept in prime condition.
This unit has been designed to slip under most vehicles without scratching the floor surface and features automatic current sensing so that it knows when it is needed.
The intelligent sensing in SSU2-50/S determines exactly when support is required to minimize unnecessary noise and power consumption.
An expanding range of adapters are also available to allow simple connection directly to the vehicle battery or via distribution points.
Approved by JLR for use in showrooms.
CSU2-50 provides a stable voltage and up to 50 amps of fully regulated power to prevent loss of charge and damage to the battery.
CSU2-50 can be used with any 12V automotive battery including AGM, GEL and LiFeP04.
In SSU mode, when the battery is charged the CSU is a regulated power supply to sustain accessory loads and offset parasitic drain with battery state detection, ensuring safe prolonged use.
In BSU mode a continuous power source is supplied to the battery until physically removed.
CSU current mode of operation:
To select BSU function - Turn the mains on without the battery connected and wait for two beeps within 2 seconds. Then connect the battery.
To select SSU function - Connect the battery with mains power off, then turn the mains on.
Output current display.
Reverse polarity protection.
Disconnect detection.
Comes with 4.8M lead set and 2.4M power cord.
OVERVIEW
The MPL50-LI charger from Traction has been designed with the latest workshop standards in mind.
Suitable for most common battery types – LiFePO4, Ca/Ca, Ca/Ag, AGM, GEL and conventional lead acid.
The MPL50-LI features a contactor reset mode for reactivating disabled/highly discharged LiFePO4 batteries.
As with all Traction battery chargers the MPL50-LI is manufactured at our own UK site.
MPL50-LI is available with an optional temp sensing lead set allowing the ultimate in efficient charging.
MPL50-LI also features a 13.4V constant output mode for battery support functionality at up to 50A.
MPL50-LI is compatible with CDU-1 Charge Distribution Unit.
Introducing the new SPIC-50 Battery Charger.
Lithium Ca/Ca, Ca/Ag, AGM, GEL and conventional lead acid battery types covered
Customisable Interface to battery BMS systems
Customisable charge profiles
50A Constant output function for diagnostic support
3-stage charging: CI-CV-Float
Short Circuit shutdown
Reverse Polarity Protection
Soft start
Fast constant current bulk charge
Constant voltage float/standby
Features a customisable interface to the battery BMS system with LIN bus support
Temperature adjusted charge profile for safe Lithium battery charging
Output leads zero volts until the battery is connected and the charge process started
OVERVIEW
This is a complementary product to the MPL50 charger and MPL50-Li charger that manages charging of a bank of up to 5 batteries.
It can be either placed under the MPL50/MPL50-Li charger or situated remotely by use of optional link lead.
Power is provided from the MPL50/MPL50-Li. When a battery is disconnected the unit will turn off power to the output making the leads safe from accidental shorts.
The 5 output connectors are compatible with Traction standard yellow 50 Amp lead sets.
The module input is a red 50 Amp connector. A yellow to red interface lead is provided ensuring correct connection.
The status of each channel is indicated by an LED above each connector.
Units can be daisy-chained allowing up to 17 batteries to be connected simultaneously.